BEIJING ANSHUNTAI CONSTRUCTION TECHNOLOGY CO.,LTD.
— 产品展示 —

安顺泰墙坭高强粉刷石膏

安顺泰墙坭高强粉刷石膏
【产品简介】
安顺泰墙坭高强粉刷石膏采用进口添加剂,配以国内优质填料生产制作而成, 是一种性能优良的建筑内墙及顶板抹灰新型材料,产品分底层、面层两部分,粉状,加水搅拌均匀后即可使用,是传统抹灰材料(混合灰和白水泥)的换代产品。本品无毒、无味且具有调节空气湿度、杀菌等作用,是绿色环保的健康产品。
【用 途】
本品适用于砖墙、现浇混凝土墙、加气混凝块墙、石膏砌块墙、顶棚、特别适用于砼顶板、加气砼墙面及各种保温材料的表面抹灰。
【主要成份】
半水石膏、碳酸钙、沙(底层)、缓凝剂、有机胶粉、有机纤维、添加剂等
【产品性能指标】
1.凝结时间:
初凝时间≥1小时  终凝时间≤ 8小时
2. 可操作时间:大于60分钟。
3.保水性:
面层安顺泰墙坭高强粉刷石膏≥90%,底层安顺泰墙坭高强粉刷石膏≥75%
4.强度:
抗折强度面层≥3.0Mpa,底层≥2.0Mpa ,抗压强度面层≥6.0Mpa,底层≥4.0Mpa
【产品优点】
安顺泰墙坭高强粉刷石膏是一种新型墙体抹灰材料,具有传统混合灰所无法比拟的优点和特性。隔音性能:安顺泰墙坭高强粉刷石膏在凝结过程中,内部产生微小的孔隙,因此能衰减声压,又可防止声能透射,故具有良好的隔音性能。
呼吸功能:安顺泰墙坭高强粉刷石膏硬化过程中,形成无数个微小的蜂窝状呼吸孔,当室内环境湿度较大时,呼吸孔自动吸湿;在相反条件下,能自动释放储备水分,这样反复循环,巧妙地将室内湿度控制在适宜范围之内,为居住者创造了良好舒适的生活环境。卫生保健性:石膏不但是一种绿色建材,本身也是一种药材,有消毒杀菌的作用,在石膏材料装修的房间里,细菌难以生存和传播。因此,用石膏制品取代有气味、不透气的装潢材料,对人体健康有益。用石膏粉刷的房间尤其适用于婴幼儿和老年人居住。
【基层处理及操作工艺】
1.安顺泰墙坭高强粉刷石膏前将基体表面灰尘、杂物、隔离剂等处理干净,做到平整干净,无灰尘,无油污。请根据不同基层材料适当充分喷水润湿,但不能在基体表面有水的情况下作业。
2.抹灰前对较干燥的墙面适量喷水湿润,但有明显潮湿和水珠的墙面应暂缓施工。
3.料浆配制:一次投料量应是在可使用时间内用完的料浆使用量,初凝后的料浆不得再加水搅拌使用;料浆配制必须搅拌均匀才可使用,稠度要比水泥砂浆稍稀;在气温超过℃30℃或风力在四级以上时,料浆的配制要比平常再稀一点,以保证抹灰层质量;料浆搅拌用水应是清洁无杂质的。
4.手工抹灰:根据施工情况先冲筋。冲筋的间距根据房间的高度决定,一般在墙面的底、上部冲筋两道即可。冲筋完毕后即可进行抹灰操作。
5.抹灰厚度≤2mm时,可直接使用面层型安顺泰墙坭高强粉刷石膏;抹灰厚度>3mm时,先用底层型安顺泰墙坭高强粉刷石膏打底、抹平,再用面层型安顺泰墙坭高强粉刷石膏罩面。
6.当抹灰厚度超过时,应该分层施工,每层厚度在以内,待上一层料浆终凝后再抹一下层。
7.压光应在终凝前进行,一般在抹灰后30分钟左右,用指按压表面不出现明显压痕为宜。
8.刮涂率距刮涂厚度有所不同。
【注意事项】
1.加水的石膏应在初凝前用完,初凝后的料浆不得加水使用。
2.施工完毕的墙面应避免磕碰及水冲浸泡,并要保证室内通风良好。
3.现场施工温度应超过零下5℃。
【贮存、运输和包装】
1.本品应贮存在干燥处,严禁受潮。
2.标准储存状态下储存期为12个月。
3.本品运输按《非危险品运输规则》处理。
4.储运要防潮防雨。
5.包装:20㎏/袋、
 

【产品简介】Product Profile
Anshuntai High-strength Plastering Gypsum is made of high-quality fillers and imported additives. It is a new type
of well-performing plastering material for interior walls and ceilings. The product include two versions: one for the
foundation coating and the other for the top coating. The powder-formed product can be used after well mixed
with clean water. It is a modern day alternative solution to traditional platering material (Sand Cement Plaster).
This product is not only non-toxic and odorless, but also able to regulate air humidity and disinfect the
envinroment. It is a green and safe product.
【用 途】Scope of Application
This product is suitable for surface plastering of brick wall, cast-in-place concrete wall, aerated concrete block
wall, gypsum block wall, ceiling, especially for concrete plate, aerated concrete wall, besides various insulation
materials.
【主要成份】Ingredients
Semi-hydrated gypsum, calcium carbonate, sand (the foundation version), retarder, organic rubber powder,
organic fiber, additives, etc.
【产品性能指标】Technical Parameters
1. Setting Time
Initial Setting Time ≥ 1 hour
Final Setting Time ≤ 8 hours
2. Pot Life: No shorter than 60 minutes
3. Water Retension
Top Coating Version ≥ 90%
Foundation Coating Version ≥ 75%
4. Strength
- Fracture Strength: Top Coating Version ≥ 3.0Mpa, Foundation Coating Version ≥ 2.0Mpa
- Compression Strength: Top Coating Version ≥ 6.0Mpa, Foundation Coating Version ≥ 4.0Mpa
【产品优点】Product Features
Anshuntai High-strength Plastering Gymsum is an alternative solution to the traditional wall plastering material,
Sand Cement Plaster. Comparing to the traditional material, the product has the following strengths:
- Sound Insulation: In the process of condensation, tiny pores are formed inside the product. These pores can
attenuate the sound pressure and weaken the transmission of sound energy.
- Humidity Regulation: In the process of hardening, numerous tiny honeycomb-shaped breathing holes are
formed in the product. When the indoor environment is in high humidity, the breathing holes can automatically
absorb the moisture; in the opposite situations, the reserved moisture in those holes can be automatically
released. In this way, the indoor humidity is maintained within a suitable range, creating a comfortable living
environment.
- Disinfection: Gypsum is not only a kind of green building material, but also a kind of Chinese medicine. It is said
to be able to disinfect and sterilize the environment. In the room where the gypsum material is used, bacteria are
difficult to survive. Therefore, replacing odorous and airtight finishing materials with gypsum products is a good
way to ensure health. Rooms finished by Gypsum materials are especially good for infants and the elderly.
【基层处理及操作工艺】Surface Preparation and Application
1. Before application, make sure the surface is clean and free from dust, grease or separant. Please pre-wet the
surface by spraying a proper amount (depending on the substrate materials) of water, but do not start the next
step when there is water hanging on the surface of the substrate.
2. Before the plastering, apply a proper amount of water to the wall if it is rather dry, but the next step should be
held if the wall is seen with water hanging on the surface.
3. Mixing and Blending: The dosage of product each time should not exceed the amount that may exhaust the pot
life. After the end of initial setting time, no more water should be blended into the paste for further use. Please
make sure the paste should be uniform and lump-free, and it should be a bit less thick than cement mortar. When
the temperature is higher than 30 °C or the wind is stronger than the fourth grade, the paste should be thinner
than usual to ensure the quality of the plastering. Only clean water should be used.
4. Reference Marks Placement. Place aluminum box plate on bull marks. The space between two marks depends
on the height of the wall.
5. Manual Plastering:If you wish the coating thickness to be ≤2mm, you may use the product (Top Coating
Version); if >3mm, use the product (Foundation Coating Version) as a base and levelling, and apply a second
coating upon that using the product (Top Coating Version).
6. If you wish the coating to be >3mm, multiple coatings should be applied, and each coating thickness should
not exceed the limit. On after the fianl setting time past for the first coating, a second coating can be applied.
7. Press polishing should be done before the end of final setting time, which is approximately 30 minutes after
plastering. Use your finger to press on the surface to check if it is done (if leaving no obvious print, it is done.)
8. The coating thickness can vary.
【注意事项】Precautions
1. The paste should be used up before the end of inistial setting time. After the end of initial setting time, no more
water should be blended into the paste for further use.
2. The finished wall should be kept from being bumped or contact with water, and make sure the indoor ventilation
is functioning well.
3. The temperature at the time of application should not be lower than - 5°C.
【贮存、运输和包装】Storage, Transportation and Pakage
1. This product should be stored in a dry place, and carefully kept from exposure to moisture.
2. If stored properly the product life is 12 months
3. Transportation should be arranged in accordance with Non-Dangerous Goods Transportation Regulations.
4. To keep the products from exposure to moisture and rain is the key in storage and transportation.
5. Package: 20 KG / Pack
电话
邮箱
地图
分享
联系